Choosing Clear Plastics for Optical Parts: Acrylic vs PC

A common assumption treats clear plastic as a single category: pick the grade that looks clearest, and the optical housing, light pipe, or lens mount will work. That assumption misses half the decision. Acrylic and polycarbonate are the two clear grades a CNC shop sees every week, and they trade clarity against toughness in ways that show up only after assembly, cleaning, or a drop onto the bench. Acrylic machines more easily but breaks more readily; polycarbonate survives the fall yet scratches and clouds faster. A clear plastic optical part that looks like a simple rectangle on the drawing can ship in three days in one material and crack on its second assembly in the other. This comparison lays the optical, mechanical, machining, and chemical numbers side by side so the grade is chosen on purpose rather than by appearance.

How clarity and light transmission compare

Acrylic, or PMMA, transmits about ninety-two percent of visible light, the highest figure among clear plastics, and it carries low chromatic aberration. That optical position is why lenses, display covers, and light-guide windows default to acrylic in most designs. Polycarbonate transmits eighty-eight to ninety percent, close but not equal, and it shows higher refractive dispersion, so white-light edges reveal faint color fringing on precision optics.

Surface finish follows that optical difference. Acrylic polishes to an optical grade: a flame-polished or diamond-turned acrylic surface reads as glass to the observer. Polycarbonate polishes less well and tends to haze under aggressive buffing, which limits how close a finished PC face comes to an optical window. For a viewport where transmission and flatness matter more than impact resistance, acrylic wins on the optical bench. For a protective cover behind a gasket where nobody judges the transmitted image, the two to four percent transmission difference stays invisible and toughness may dominate the choice.

Mechanical strength and temperature limits

The numbers flip once the part carries load or heat. Acrylic reaches a tensile strength of fifty to seventy MPa and notches easily; a machined corner left without a radius cracks when a screw tightens against it. Its heat deflection temperature sits around seventy to eighty degrees C, after which the material softens and creeps under clamp load.

Polycarbonate runs sixty to seventy MPa in tensile strength but absorbs impact that would shatter acrylic, and it survives continuous service from minus forty to one hundred twenty degrees C. A PC cover dropped from one meter bounces; the same acrylic cover from the same height fractures into shards. Raw stock pricing reflects that gap: PC bar runs roughly 1.5 to 2.5 times the cost of acrylic. Thermal expansion adds a further difference. Both plastics move with temperature, but PC expands slightly more and stays softer under clamping, so tight optical mounts in PC need looser tolerances or a metal shoulder to hold alignment. The polycarbonate-versus-acrylic breakdown covers these property tables in full.

Assembly stress deserves its own review because it breaks acrylic more often than impact does. A bolt pulled tight through a plain hole concentrates force at the notch; a plastic boss, clearance washer, or metal sleeve spreads that load and keeps the clamp from cracking the face. Acrylic parts should carry generous corner radii, avoid press fits against the brittle edge, and use standoffs rather than direct clamping on the optical surface. PC tolerates the same fastening arrangement more forgivingly, but its softness means a tight screw can creep under repeated thermal cycling and loosen over time, which calls for a threaded metal insert where retention matters. Drawing the fastener load path early prevents a machining-accurate part that fails at assembly.

How acrylic and polycarbonate machine differently

Acrylic cuts like glass. The shop uses sharp tools, a high spindle speed around four thousand to eight thousand RPM for a six-millimeter end mill, and a light feed. A worn tool or a feed that runs too fast leaves stress cracks and a feathered, frosted edge along the cut.

Coolant becomes a specific risk on acrylic. Flood coolant can thermal-shock the part and initiate micro-cracks, so shops prefer a compressed air blast to clear chips rather than liquid. Polycarbonate machines softer and gums up when the tool turns dull, because the material melts and smears at the cutting edge; PC wants moderate speeds, sharper tooling, and tolerates a mist coolant. Both plastics trap stress when material is hogged out in one heavy cut, so the routine divides roughing into two light passes followed by a finish pass. Polishing the edge consumes the remaining time: acrylic finishes with flame or vapor, while PC needs hand polishing and takes noticeably longer. The acrylic machining guide covers the tooling and feed settings that keep the edge clear.

Chemical, scratch, and UV exposure differences

Acrylic resists many household cleaners but cracks on contact with alcohol, acetone, and aromatic solvents. Wiping an acrylic window with isopropyl can craze the surface overnight, which matters for any enclosure cleaned in a production or laboratory setting. Polycarbonate shrugs off those same alcohols but scratches so easily that a dry wipe with a paper cloth leaves visible marks across the face.

For optical parts sealed inside an enclosure, scratch resistance becomes a non-issue while chemical resistance may decide the grade. For a part users touch and clean repeatedly, PC requires a hard coat that adds process cost and lead time to the finished component. UV exposure divides the two materials outdoors. Unstabilized outdoor acrylic yellows over five to ten years, while PC yellows faster, in two to four years, and then turns brittle. Specifying a UV-stabilized grade remains necessary whenever daylight reaches the part, and the drawing should name the grade and trade name rather than leave the buyer to write only clear plastic.

Dimensional tolerance on clear plastic behaves differently from metal. Because both grades expand more than aluminum or steel and relax after machining, tight positional tolerances on a large cover usually prove unrealistic even when the machine can hold them on the day of cut. Leave clearance around mounting holes, design slots where thermal movement must be absorbed, and separate the optical reference face from the clamped mounting features so temperature change does not shift alignment. Shops familiar with transparent stock can suggest where a tolerance should loosen without affecting the optical function; asking that question before release avoids a first article that measures correctly in the machine room but binds once installed.

Why a two-material build often wins

No single grade satisfies every requirement of an optical assembly. A design that needs a crystal-clear face and a tough surrounding carrier often forces a compromise when one material must serve both roles: acrylic on the carrier side cracks under impact, while PC on the optical face cannot match transmission and polish.

The honest answer for those mixed requirements becomes a two-material build: a thin acrylic optical face bonded into a PC or metal carrier that absorbs impact, clamping load, and assembly stress. The carrier handles structural duty while the acrylic face handles light, which keeps each material in the condition it performs best. Bonding surfaces, adhesive chemistry, and thermal expansion mismatch between the two materials then enter the DFM review, since a poor bond delaminates under the same temperature cycle the assembly was meant to survive.

What to write on the optical-part drawing

Grade selection follows the operating conditions rather than a generic preference. Pick acrylic for an optical window, lens, or light guide where clarity and polish dominate, provided the part runs below seventy degrees C, avoids impact and assembly stress, and contacts only water-based cleaning agents. Pick polycarbonate when the part must absorb impact, survive higher temperature, tolerate assembly stress, or resist the cleaning chemistry on the production line.

Send the drawing with the operating temperature range, the cleaning chemistry used on site, and the required transmission figure, so the shop can flag a grade that fails one of those conditions before machining begins. Note any required hard coat on PC and any flame or vapor polish specified on acrylic. The clear plastic machining guide and the optical components overview list the remaining design rules that keep these parts from cracking, crazing, or clouding after delivery.

⚙

Ready to Start Your CNC Project?

Get a free quote within 24 hours. ISO 9001 certified, 20+ years experience, low-volume friendly from 1 piece.

Get a Quote