ABS is the plastic everyone has machined at least once, and the one that bites back most often. It cuts clean, it is cheap, and it accepts paint, plating, and glue better than most engineering plastics. It also warps, softens under heat, and absorbs enough moisture to move 0.1 mm on a 100 mm part if the storage environment changes. Most ABS complaints on the shop floor are not about the cut; they are about dimensions shifting between the machine and the customer’s caliper. This article covers the setups and design calls that keep an ABS part within ±0.1 mm from first chip to shipment.
Why ABS moves after the cut
ABS is amorphous, which sounds like a liability and is actually helpful: it does not crystallize the way nylon or polypropylene does, so it does not shrink dramatically from a mold. But it does relax. Machining releases residual stress built into the extruded sheet or bar during cooling. A part that measures 50.00 mm at the machine may be 49.92 mm three days later as the material relieves. Moisture adds a second shift: ABS absorbs about 0.2-0.4 percent by weight in a humid week, and that swelling shows up as slow dimensional drift. The fix is not a tighter tolerance on the drawing. It is stress-relieving the blank before machining and letting the part sit in the shop environment before final inspection. Stress-relieved ABS bar stock is worth the small premium if the tolerance matters.
Cutting parameters that keep edges clean
ABS melts around 100 C, and the enemy of a clean edge is heat. Use sharp, 30-degree-rake, polished-flute carbide or HSS end mills. Run spindle speeds around 3,000-5,000 RPM on a 6-12 mm tool, and feed at 0.03-0.08 mm per tooth, so the chip shears instead of rubbing. Climb mill every time; conventional milling on a soft plastic rubs the edge and leaves a frosted, melted burr that is almost impossible to debur cleanly. A light air blast clears chips without the thermal shock that flood coolant can cause on thin sections. Avoid very small tools at high speed, because heat builds fast in a 3 mm end mill. If the edge feels stringy or rubbery, the feed is too slow or the tool is dull, not the plastic’s fault. The ABS machining guide covers the same parameters with more setup detail.
Clamping, fixturing, and thin walls
ABS creeps under clamp load. A part held at vise torque meant for aluminum will deform within minutes, spring back after it comes off, and measure wrong. Use soft jaws with spreader plates, clamp on a thick section rather than a thin wall, and torque the vise like you would on plastic: light, even, and re-check after the first pass. Thin walls below 1.5 mm chatter badly on ABS. If the design needs a thin rib, machine it in a light finishing pass with the cutter centered on the rib rather than side-milling it. Deburring ABS is gentle work. A hand knife is fine; a tumbler can stress-crack the edges. Ultrasonic cleaning in alcohol is a no-go, because ABS crazes under ketones and many solvents; wipe with mild soap and water. The CNC deburring guide lists the methods that do not damage plastic.
Paint, glue, and assembly after machining
ABS is the friendliest engineering plastic for secondary finishes. It takes spray paint without primer adhesion problems, it chromes for decorative parts, and it glues with cyanoacrylate, epoxy, or ABS cement. Those processes add their own dimensional risk. Paint film adds 15-40 micrometers per coat, which can close up a tapped hole or a press fit. Design clearance before painting, or specify paint on non-critical surfaces. Solvent cement melts the surface and can warp a thin wall in minutes, so use it on rigid joints only. If the part is plated, ask the shop which grade of ABS they are running; electroplating ABS requires an additive grade, and generic machining ABS will not plate. The CNC plastic machining guide covers the grade-by-grade secondary-finish choices.
The checklist for a stable ABS part
Six choices prevent the usual surprises. Order stress-relieved blanks when tolerances matter above ±0.1 mm. Allow 24-48 hours between roughing and finishing so stress relief happens before the final cut. Specify climb milling and sharp tooling on the drawing’s process notes. Clamp on thick sections and keep walls above 1.5 mm. Call out which surfaces are paint- or assembly-critical so the shop knows where to hold the finish. And pack the part dry in a VCI or poly bag for shipping, because a wet shipment introduces the moisture shift you were trying to avoid. Done this way, ABS machines like a dream and holds its numbers. Done the other way, it is the plastic that everyone complains about. The HDPE machining guide covers the neighboring plastics if your design crosses material lines.
