A semiconductor bracket looks from the drawing side like any other machined aluminum part, and a shop that treats it like one will fail chamber qualification. Ordinary CNC work tolerates trapped chips in threads, absorbed coolant, and a porous anodized layer that breathes out under vacuum. Inside processing equipment, those same details release gas, shed particles, and disturb a 300 mm wafer lot worth tens of thousands of dollars. Machining for the semiconductor industry is therefore not a looser or tighter version of general aluminum work; it is a separate discipline built around vacuum compatibility, clean surfaces, stable flatness, and paper that traces every feature back to a heat lot. This guide explains what the equipment environment demands, which materials hold up, and what a buyer should ask before releasing a purchase order.
What a chamber actually demands of the metal
Processing chambers run at vacuum as deep as 10 to the minus 7 Torr, and wafer stages move in micrometer-scale steps. A single particle loosened from a bracket, a gas discharge from trapped moisture, or a plate that bows after installation can contaminate a run the fab cannot afford to repeat. The environment rules out shortcuts a general-purpose shop might take without thought. Coolant residue baked out slowly over hours in a vacuum pump wastes chamber cycle time and leaves hydrocarbon residue on the first wafers. Chips hidden in blind holes or tapped threads become a particle source the machine cannot remove once the chamber closes. Surface porosity that would be invisible on a structural bracket acts as a reservoir for outgassing. Every machining choice in this industry answers back to one question: will the component stay clean, flat, and dimensionally stable inside a sealed, evacuated environment?
The parts that live inside vacuum equipment
Semiconductor machining covers a recognizable family of components, each with its own critical feature set. Chamber walls and baseplates carry vacuum seals, bolt patterns, and mounting faces that must stay flat across temperature. Lift pins and support pads contact the wafer or its holder directly, so surface integrity and absence of particles matter more than raw strength. Electrode plates face the plasma and must hold a uniform flat surface through repeated thermal cycles. Gas distribution bars carry internal channels and precision-machined exit ports whose spacing defines the gas flow. Robot end effectors move wafers between stages, combining lightweight stiffness with smooth, non-shedding contact surfaces. Fittings, spacer blocks, and shielding plates fill the space between these main components, but even secondary parts inherit the cleanroom and vacuum rules once they sit inside the chamber envelope. A shop bidding this work should identify which feature seals, which feature contacts the wafer path, and which surface faces plasma before quoting a process.
Which stock goes to which feature
Aluminum 6061-T6 remains the workhorse. It machines predictably, anodizes cleanly, and holds flatness after stress relief, which makes it the default for structural chamber frames, baseplates, and most non-wetted hardware. 7075 stays out of the chamber itself: its higher copper and zinc content makes it more prone to corrosion under plasma exposure and to stress-corrosion cracking, so it appears only on structural frames outside the vacuum envelope. For wetted parts and gas lines that meet halogen plasmas, stainless 316L offers the required corrosion resistance. Plasma-facing ceramics and quartz handle the most aggressive surfaces, but those components are normally ground or lapped rather than milled on a standard machining center. Engineering plastics fill insulator and feedthrough roles: PEEK for high-temperature feedthroughs, G10/FR4 for lower-cost insulating plates. Our G10 FR4 machining guide covers the dust control and tooling side of those insulating parts, while the optical machining article describes the ultra-flat substrate work that overlaps with semiconductor wafer stages.
Flatness and datums on oversized plates
A chamber baseplate around 600 mm on a side commonly carries a flatness callout of 0.02 to 0.05 mm across the whole surface, with parallelism between mounting faces under 0.03 mm. Commercial sheet metal and a quick vise cut cannot reach that band. The process starts with stress-relieved stock. A rough cut removes roughly one to two millimeters per side, the plate then goes through a thermal relaxation cycle, and finish cuts alternate between opposite faces so material removal does not bow the component as one side thins. Fixturing stays light. Vacuum chucks or low-pressure soft jaws replace a vise crushed down on the plate, because clamp force leaves a bowed part once released. The last 0.05 mm of stock comes off with a climb-milled face mill running 8,000 to 12,000 RPM at a light feed, and the plate rests for 24 hours before the final CMM check so residual stress can equalize. Shops that skip that waiting period hand over plates that measure flat on the coordinate machine and bow by around 0.04 mm once installed on the chamber frame.
Measurement conditions matter as much as the cut itself. Large plates inspected straight after machining carry the thermal gradient of the shop, and a part held flat on the granite table can show a clean reading that reverses once it sits free on the chamber frame. Datum selection should follow the actual mounting interface rather than the most convenient edge on the mill, because a datum that does not match installation geometry builds error into every bore and bolt pattern referenced from it. Operators record the CMM temperature, probe strategy, and datum chain alongside the dimensional report, so a downstream engineer can judge whether a measured deviation comes from the part, the fixture, or the inspection environment.
Surfaces that seal a vacuum without shedding
Inside a chamber, a matte as-milled surface becomes a particle trap. Visible chamber walls receive a glass-bead blast or chemical film, then a Type II or Type III anodize, with the whole part electrochemically sealed afterward. The anodize thickness is chosen by function rather than appearance: 10 to 15 microns of Type II coating suits general walls, while 25 to 50 microns of hard coat covers sliding surfaces. The layer seals the aluminum against plasma and provides a hard, non-shedding face; outside the chamber, standard clear or black anodize remains acceptable. Threaded holes that see vacuum should take a stainless threaded insert rather than a tapped aluminum thread, because aluminum threads gall and shed particles over repeated assembly cycles. Where electrode faces need extreme uniformity, machining is followed by a lapping step that reaches Ra 0.1 micron, a process detailed in our mirror finish machining guide. The discipline carries over to adjacent equipment: the data center hardware article shares the same low-particle, high-flatness requirements on a different industry.
Questions that separate qualified shops
Three questions sort shops that genuinely do semiconductor work from those that simply mill aluminum. Ask whether the supplier operates a dedicated cleanroom wash and pack area, and what cleanliness class it maintains. Ask how stress relief is handled on large plates: request the rough-cut, aging, and finish-cut sequence in writing rather than accepting a general statement about quality control. Ask whether every batch can ship with a full material certificate, an anodize thickness report, and a CMM flatness report. A blank answer on any of those points usually means the part will look acceptable on the bench and fail chamber qualification later.
First-article dimensional reports accompany every new component, and a traceability record ties each serial number to its heat lot, the operator, and the machine that cut it. That paperwork is not administrative overhead. It is what lets a fab trace a contaminated wafer batch back to a specific machining run if something goes wrong. Buyers should also state on the drawing which surfaces contact the wafer path, which faces seal vacuum, and where plasma exposure occurs, because those callouts decide the cleaning sequence, coating choice, and inspection plan. The supplier that asks those questions during quoting, rather than after a failed qualification, is the one likely to hold the vacuum-compatible standard this industry requires.
Document packages for repeat chamber hardware normally bundle the material certificate from the mill, the CMM dimensional report for first articles and sample units, the anodize or plating thickness record, cleaning and packaging confirmation, and the batch traceability sheet. Missing one of these on a recurring order often delays chamber assembly more than a dimensional deviation, because the fab cannot release hardware into the cleanroom without the record that proves its surface was processed to the vacuum-compatible standard. Early in the relationship, asking which reports the shop can produce on every batch avoids discovering the gap after production tooling has already been committed.
