Spindle speeds on a CNC lathe run from roughly 1,000 to 6,000 RPM for steel and up to 3,000 to 10,000 RPM for aluminum and brass, and the part rotates while the cutter feeds against it. Milling and turning form the two pillars of CNC machining, cutting material in opposite directions: in milling the tool spins and moves across a stationary part, while in turning the part spins and a single-point tool feeds across its surface. That one difference decides which shapes a lathe produces well and which it cannot: anything with a round cross-section. Shafts, bushings, couplings, valve bodies, threaded fittings, and pulleys all begin on a lathe. Understanding what the spindle and tool actually do makes both drawings and quotes easier to read.
Spindle motion, axes, and how the cut forms
A CNC lathe holds the raw bar in a chuck or collet and spins it at programmed speed. A carbide insert mounted on the turret moves in two axes: the X axis shifts the tool toward or away from the centerline to control diameter, and the Z axis moves along the spindle to control length.
As the spindle turns and the insert feeds, it peels a thin layer of metal off the outside of the bar. Depth of cut runs 0.5 to 3 mm on a roughing pass and 0.1 to 0.3 mm on a finishing pass, at a feed of 0.1 to 0.3 mm per revolution. The chip curls off the rotating bar and clears the cut zone. Every lathe operation is a variation on this feed against spinning stock.
Common turning operations on the lathe
Facing trims the end of the bar flat so the part carries a square reference. OD turning steps the outside diameter down from stock size to the drawing diameter. Boring performs the same work inside, taking material from the wall of a pre-drilled hole to reach a precise bore. Parting-off cuts the finished piece away from the bar at the required length.
Grooving cuts a shallow recess for an O-ring or snap ring. Threading runs the tool in multiple passes at a feed matched to the thread pitch, so a 1.5 mm pitch thread receives a 1.5 mm per revolution feed repeated over five to ten light passes. Drilling advances a drill down the centerline from the tailstock or a driven tool. A modern turning center with live tooling can also mill a flat or drill a cross hole while the part spins, collapsing several setups into one. The turning operations guide lists each cut with its typical insert and feed.
Concentricity, tolerances, and surface finish
Turning naturally produces good concentricity, because every turned feature shares the same centerline. A shaft turned, bored, and threaded in one setup holds bore and OD to a runout of 0.005 to 0.01 mm easily, which is why pulleys, rollers, and spindles are turned rather than milled.
Diameters hold ±0.01 to 0.02 mm routinely and ±0.005 mm on good machines; length stays a little looser, around ±0.02 to 0.05 mm, because parting-off leaves a small burr usually faced in a secondary operation. Surface finish depends on insert nose radius and feed: a 0.4 mm nose radius at 0.1 mm per revolution leaves about Ra 1.6, while dropping feed to 0.05 mm per revolution reaches Ra 0.8. Finer than that calls for grinding or a polish. The milling-versus-turning comparison explains when a round part still belongs on a mill.
Bar stock, chucks, and collet workholding
Most turned parts start from round bar fed through the spindle, which keeps material cost low and cycles short: a 30 mm bar turns into a 28 mm shaft with almost no waste. Chuck work for larger diameters, or for cast and forged blanks, uses a three-jaw or four-jaw chuck and consumes more setup time.
The collet setup common on Swiss-type lathes holds the bar very close to the cut, letting shops turn long, slender shafts without deflection. That Swiss approach produces the tiny precision pins found in medical and instrumentation hardware. Holding method directly determines how slender a shaft can go before the bar flexes away from the cutter.
The geometry limits a lathe cannot cover
Turning works only around one rotational axis. A part with flat sides, pockets, or features on multiple faces that do not revolve around that axis cannot be completed on a conventional lathe alone. It moves to a mill, or a turn-mill machine with live tooling handles both in one chuck.
Recognizing that boundary at the drawing stage prevents a quote that promises turned geometry the process cannot hold. Cross holes, milled flats, bolt patterns, and asymmetric bosses either add live-tooling operations or a separate milling setup, each carrying its own setup cost and tolerance alignment. The live tooling guide covers what a mill-turn center adds beyond the basic lathe.
What buyers should specify on a turned drawing
When sending a drawing with turned features, mark diameters and bores with real tolerances rather than leaving them at the shop default, because that default runs looser than precision work. Specify the thread class, the surface finish on sealing faces, and any runout or concentricity callout on rotating assemblies.
Material choice changes cycle time: free-machining brass and leaded steel cut fast, while stainless and titanium run at roughly half the speed and wear inserts faster. Lead time for a turned part usually stays short, since programming a turning job remains simpler than a multi-sided mill program. For a shaft, bushing, coupling, or basically round housing, turning remains the right process; the shafts machining guide and the turning process overview collect the design rules that keep cost down.
