G10 and FR4 look like flat green or tan laminate board and machine like something between epoxy and sandpaper. The resin cuts cleanly, but the woven glass fibers are abrasive, and they blunt high-speed steel tools in minutes. Get the tooling wrong and you leave frayed, blackened edges and a cloud of irritating dust in the shop. Get it right and you produce insulating spacers, fixtures, probe plates, and electrical substrates that hold flatness and dimension for years. This guide covers the practical differences between the two grades and the setup that keeps edges clean.
G10 versus FR4, and why it matters
Both are glass cloth impregnated with epoxy, pressed into laminate. The difference is the flame-retardant treatment: FR4 is the fire-rated version with a brominated additive, while G10 is the base, non-FR grade. For most mechanical parts the two machine nearly identically, and buyers often use the names loosely. The material is an insulator, dimensionally stable, and nearly immune to moisture compared with nylon or UHMW. It machines to tight tolerances, holds flatness, and does not creep under clamp load the way soft plastics do. That combination makes it a fixture material: probe plates, insulation blocks, and vacuum table sacrificial sheets. The G10 and FR4 machining guide goes deeper on tooling and dust control, and the carbon fiber machining guide shows how the same composite logic extends to CFRP.
Tooling, speeds and feeds
Use solid carbide or diamond-coated tooling. High-speed steel will wear dull after a dozen cuts through the glass weave, and a dull tool frays the edge rather than shearing it. Run spindle speed high, roughly 8,000 to 18,000 RPM for a 6 to 12 mm end mill, with moderate feed that keeps the chip moving. Light, climbing cuts give the cleanest edge because they shear the fiber instead of pushing it. Do not take a heavy final pass that dwells, because heat softens the epoxy and leaves a melted, blackened zone around the cut. For thin G10 sheets, support the material firmly on a vacuum table or a sacrificial backing board, because the laminate will splinter on breakthrough if it flexes. Drill with carbide twist drills or carbide printed-circuit-board drills at high speed, and back the sheet to prevent delamination on exit.
Dust, edge quality and delamination
The dust is the real issue. Glass fiber dust is fine, airborne, and irritating to skin, lungs, and eyes. Every G10 or FR4 machine needs dust extraction at the cutter, and the operator should wear a mask and eye protection. Do not use flood coolant, because it turns the dust into a slurry that clogs ways and carries glass grit into the machine’s linear rails. Instead, use a high-pressure air blast with a nearby vacuum, or a dedicated composite machine with a ducted enclosure. Edge quality tells you whether the cut is right: a clean, straight edge with white, sheared fiber ends means the tool is sharp and the feed is correct. Frayed, fuzzy edges mean a dull cutter. Delamination at hole exits means the drill was pushing rather than cutting, and backing the sheet or using a sharper drill fixes it.
How it sits next to other machinable plastics
G10 is not a general plastic substitute. It is stiff, rigid, and brittle compared with nylon or UHMW, and it will crack if clamped over a sharp edge. Use it when the part needs electrical insulation, flatness, and dimensional stability in a flat or block geometry. For sliding wear parts, UHMW and nylon win because they are tough and self-lubricating, as the UHMWPE tight-tolerance guide shows. For tough, low-cost sheets that need impact resistance, HDPE behaves very differently, as the HDPE machining guide covers. G10’s niche is not structural toughness but precision insulation and fixture stability, and that is where it beats both. Specify it when the drawing calls for a flat, non-conductive, dimensionally stable plate, and skip it when the part needs to flex or absorb impact.
Getting the part right the first time
Order G10 or FR4 in the thickness you need rather than milling it down from a thick slab when flatness matters, because stress release after a heavy removal can warp thin plates. Let the laminate acclimate to shop temperature before final cuts, and machine critical features with a light finishing pass once the slab has relaxed. Deburse edges lightly by hand with a fine abrasive, because aggressive tumbling frays the glass. Store finished parts flat, because a thin G10 sheet warps if leaned on edge. A well-machined G10 part looks crisp and matte, with no fray or burn, and it will hold its tolerance for years in an electrical fixture. Treat it as the abrasive composite it is, respect the dust, and the parts will machine like the stable insulator the drawing expects, with clean edges and reliable registration over the life of the fixture.
