CNC Machining Plastics: A Complete Material Guide

Machined plastic parts get specified for three reasons: weight, electrical insulation, and cost. The trap is that plastics do not behave like metal on the machine — they soften, deflect, and expand, and a feed rate tuned for aluminum will leave a melted edge or a chipped corner. This guide covers the plastics that machine well, the cutting parameters that keep them clean, and the design rules that keep tolerances honest.

Which plastics actually machine well

The machinable shortlist is shorter than the plastics catalog. Acetal (POM, Delrin) is the benchmark: stiff, dimensionally stable, low moisture uptake, and it cuts cleanly to tight tolerances — it is the default for gears, bushings, and bearing surfaces. For the cutting details and achievable tolerances, see our machining acetal guide. Nylon (PA6, PA66, and glass-filled grades) is tough and wear-resistant but hygroscopic, so it moves with humidity and needs stress-relieved blanks for precision work. PTFE machines terribly — it is soft, gummy, and dimensionally unstable — but when the application needs its chemical resistance and low friction, you accept slow speeds and loose tolerances. PEEK is the high-end choice: strong, stiff, and stable up to 260°C, but it costs as much as metal and demands carbide tooling and rigid setups. ABS, polycarbonate, and acrylic machine fine with sharp tools and modest feeds; acrylic in particular is a common precision choice because it is clear, stable, and polishes well.

Cutting parameters that keep plastic clean

The enemy of a good plastic finish is heat. Plastics melt and smear when the cutting edge dwells, so the general recipe is sharp tooling, moderate spindle speed, and a feed rate that keeps the chip moving. Climb milling is almost always right — it gives a clean shear cut instead of the smeared edge that conventional milling leaves on soft material. Keep the tool sharp: a dull cutter on plastic is worse than on metal, because it pushes the material instead of cutting it and leaves white, burnished zones. Coolant policy splits opinions; a light air blast or flood mist clears chips without the thermal shock of a heavy water flood on some grades, while acrylic can crack from sudden temperature change. Test on a scrap piece when the finish is critical, and note the parameters that worked — the difference between a frosted edge and a clear edge is often just feed rate.

Tolerances, thermal behavior, and design rules

Plastics expand roughly five to ten times more than aluminum per degree of temperature, so a 50 mm part can move 0.1-0.2 mm between a cold shop and a warm one. Machine parts to tolerance at the temperature they will be measured, and hold critical dimensions with a stable fixture, not with clamping pressure — most plastics creep under clamp load. Wall thickness and support matter more than in metal: thin plastic walls deflect during cutting, so keep machined walls above 1.5 mm where possible, and support slender features with soft jaws or fixturing. Bosses and ribs should be generous, and sharp internal corners should be avoided — not just because of tool reach, but because plastics notch easily and crack from stress concentration. Threads in plastic are a classic failure point: use thread-forming inserts or oversized holes with inserts, because a tapped thread in nylon or acetal strips out under repeated assembly.

When plastic is the wrong answer

If the part carries real load, sees high temperature, needs EMI shielding, or must hold tight tolerances across a wide temperature range, metal is usually the honest answer — or a hybrid where a metal insert carries the load and plastic handles insulation and weight. If the part must survive UV exposure outdoors, several plastics degrade without additives, so check the specific grade. And if the quantity justifies it, injection molding beats machining on cost per part once volume climbs past the low hundreds; machining is the right call for prototypes, low volumes, tight tolerance work, and geometries that would need expensive molds. For a deeper comparison of the main plastic grades, our material selection guide and the acetal-versus-nylon comparison cover the trade-offs with real numbers.

Specifying the part so the shop quotes it right

Write the plastic grade and trade name on the drawing — Delrin 150 vs 570 is not a cosmetic difference, and a glass-filled nylon behaves differently from an unfilled one. State the operating temperature and any chemical exposure, because those decide between PEEK and PTFE more than price does. Call out critical dimensions with real tolerances instead of leaving everything at the default, and note which surfaces are cosmetic so the shop knows where finish matters. One question saves most quoting mistakes: ask which grade the shop stocks in bar stock. Stocked grades quote fast and ship fast; a special order adds lead time and minimums. That single conversation, held before the file is sent, is the cheapest design review you will ever do.

⚙

Ready to Start Your CNC Project?

Get a free quote within 24 hours. ISO 9001 certified, 20+ years experience, low-volume friendly from 1 piece.

Get a Quote