How to Get Accurate Quotes for Prototype Parts

You send the same STEP file to three shops and get back USD 180, USD 420, and USD 95. One of these is not a bargain and one is not a rip-off — they are all reading different parts of the same model. A prototype quote is only as good as the information behind it. The gap between a guess and a firm price is usually one or two missing details, and closing that gap is a process you control, not luck. Here is the workflow that turns a loose RFQ into a quote you can actually trust.

Start with what the shop needs to price time

A prototype quote is built around machine time, and machine time comes from geometry. The programmer has to estimate how many setups, how many tools, and how long the cycle runs. If the file is missing information that changes any of those, the estimator pads the number to cover the unknown. Undefined tolerances on a bore, an unspecified finish on a visible face, a material name that could be 6061 or 7075 — each unknown adds a safety margin. The first step toward an accurate quote is removing those unknowns before you hit send. The quote request guide we wrote breaks the RFQ into the exact fields a shop prices against.

What to send the first time

Five things move a quote from a range to a number. A STEP model plus a PDF drawing, with the revision matching on both. A named material and temper. A finish statement that says exactly what you want, including “as-machined” if you want nothing. The critical tolerances circled rather than a blanket ±0.05 on everything. And the quantity — one prototype versus ten changes the setup spread completely. Add a short note on what the part does and how it assembles, because that tells the estimator which features are worth the extra time. Shops that offer a free DFM review will often flag the design issues for free while they quote, and that feedback is part of an accurate price, not a sales pitch. The accurate quotes guide goes through these fields one by one.

How a prototype quote is really built

Behind the number are fixed costs and variable costs. Programming, fixturing, and setup are fixed — they are the same whether you order one part or ten. Material is usually the smallest line on a prototype quote, because a billet of 6061 or a slab of aluminum costs a few dollars. Machine time is variable and grows with complexity: deep pockets, tight corners, thin walls, and exotic materials all extend the cycle. Inspection adds a chunk if you ask for a CMM report. When one shop quotes USD 95 and another USD 420 for the “same” part, the low one is usually pricing raw machining with no finish, no inspection, and a best-guess setup, while the high one priced the finish, the cert, and the unknowns. Comparing them apples-to-apples means asking both what is and is not included.

Common mistakes that wreck the price

Three errors distort more quotes than anything else. The first is sending a model with no drawing and letting the shop assume default tolerances that turn out tighter or looser than you wanted. The second is quoting one quantity but planning to order five — the setup cost divides across parts, so a ten-piece order often costs only 20 to 40 percent more than a one-piece order, not ten times. The third is revising the file after the quote, which restarts programming; every revision after pricing is a new engineering charge. The quote comparison mistakes guide lists the errors buyers make when they line up three prices side by side, and most of them trace back to an incomplete RFQ.

Getting to a number you can rely on

Treat the first quote as a conversation, not a verdict. When a price looks high, ask the estimator which features drive the time and whether a design change — a corner radius from R0.5 to R2, a looser tolerance on a non-critical bore, a switch to stocked material — brings it down. Most shops will tell you, because they want the job. When a price looks surprisingly low, ask what is excluded: finish, certification, shipping, or the second operation that the geometry actually needs. An accurate prototype quote is one where both sides know what is included, what is assumed, and what happens if the drawing changes. Run that loop once on your first part and the next quote comes back firm on the first try. For bringing the cost itself down, the prototype cost reduction guide covers the design moves that lower machine time without changing function. A firm quote also locks the scope, so a later “that was not included” surprise becomes a documented change order rather than an argument about what was agreed.

⚙

Ready to Start Your CNC Project?

Get a free quote within 24 hours. ISO 9001 certified, 20+ years experience, low-volume friendly from 1 piece.

Get a Quote