Concentricity vs Runout: Which One Do You Really Need?

Two GD&T symbols show up on almost every turned part, and buyers mix them up more than any others: concentricity and runout. Both look like circles. Both relate to a shaft or a bore being centered. Yet they measure different things, cost different amounts to inspect, and mean different things when the part runs on a bearing. Specify the wrong one and you either pay for inspection you did not need or ship a part that wobbles in service. Here is the difference in plain terms and how to choose.

What concentricity actually controls

Concentricity controls the midpoint of a feature relative to a datum axis. On a turned shaft, you slice the cylinder into cross-sections, find the center of each cross-section, and require all those centers to sit inside a cylindrical tolerance zone around the datum axis. It is a relationship of axes, not surfaces. It ignores roundness, taper, and surface waviness — two surfaces can be perfectly concentric in their midpoints yet wildly out of round and still pass. The catch is measurement. Finding the midpoint of a circle requires rotating the part on a high-precision spindle and taking many readings, which is slow and usually needs a dedicated gauge or a CMM with a rotary table. That is why concentricity costs real inspection money.

What runout actually controls

Runout is simpler and stricter. Circular runout measures the full movement of the surface as the part rotates one revolution: a dial indicator on the surface, one turn, and the needle’s total swing must stay inside the tolerance. It catches every wobble, ovality, and local bump because it looks at the actual surface, not its center. Total runout sweeps the indicator along the whole length of the surface over several rotations, controlling both the circular form and the axis direction in one callout. For a shaft that spins, runout is what matters, because a bearing cares about how the surface itself moves, not about a theoretical midpoint. Our GD&T basics guide walks through these symbols with datum examples.

The numbers in practice

A typical turned shaft might carry a total runout of 0.02 mm between the two bearing journals, or a circular runout of 0.01 mm on a seal surface. A concentricity callout, by contrast, might read 0.05 mm between a bore and an OD — looser on paper, but harder and more expensive to verify. The cost difference is real. Checking runout takes minutes on a roll test or with a dial indicator. Checking concentricity means a CMM routine that samples a dozen points per section, and on a batch of 50 parts that inspection time adds up. The CMM inspection guide explains how shops actually verify each type of callout, which helps you read the inspection report you get back.

Which one your part needs

Choose runout when the feature rotates against another surface: bearing journals, seal surfaces, O-ring grooves, pulley bores. Runout directly controls the wobble that causes vibration, seal wear, and runout noise. Choose concentricity only when you genuinely care about the midpoint relationship — for example a bore that must balance mass around an axis, or a geometric relationship where surface form is already controlled separately. Most buyers who write “concentricity” on a drawing actually want runout, because they care about how the shaft behaves when it spins. If you are unsure, replace a loose concentricity callout with total runout; it is almost always the tighter, more useful, and easier-to-inspect control on a turned part. The positional tolerance MMC guide covers the related callouts that show up next to these on machined drawings.

The decision rule

One question settles it: does the surface rotate against something? If yes, spec runout — circular runout for a single cross-section, total runout along a length. If no, and you only need the axes to share a center, concentricity may be the right call, but budget for the inspection method it requires. And before you tighten either number, check what the process can hold. A live-tool CNC turning center routinely holds total runout around 0.01 to 0.02 mm on a single setup; a part machined in two setups loses that alignment and you may need 0.05 mm or looser. Match the tolerance to the process and the inspection, and the turned shaft will both pass and run true. Also check how the part is held during the check: a long shaft supported between centers reads differently than one gripped in a three-jaw chuck, because the chuck can slightly bow the part. When you ask for a runout report, note the datum setup on the drawing so the inspector measures the same axis you designed against. That keeps the report from contradicting the bench test later, and stops a part that passed inspection from failing on the assembly floor. Our shaft machining guide goes deeper into how these features are actually produced.

⚙

Ready to Start Your CNC Project?

Get a free quote within 24 hours. ISO 9001 certified, 20+ years experience, low-volume friendly from 1 piece.

Get a Quote