Internal threads are the most common way a machined part gets assembled, and the most common way it fails. A stripped boss, a tap broken off at the bottom of a blind hole, or a thread that will not start clean sends parts back to the shop. Most of those failures are designed in, not machined in. The tap drill size, the hole depth, the material, and the depth-to-diameter ratio are all decided on the drawing before the shop ever touches the machine. Design the threaded hole right and tapping is a routine operation; design it wrong and every batch loses a few parts.
The drill size and the depth rule
The tap drill sets how strong the thread is. Drill it too small and the tap binds and snaps; drill it too large and the thread has too little engagement and strips under torque. Standard tap drill charts give the right number — for an M6 thread in steel, the tap drill is 5.0 mm, leaving about 75 percent thread engagement, which is the sweet spot for strength without tap stress. In softer materials like aluminum or plastic you can run a slightly smaller drill for more engagement, because the tap cuts easily. The depth rule is the other half: a tap cannot reach the bottom of a hole, so leave a clearance below the thread depth. For a tapped hole that needs 10 mm of thread, drill at least 13 to 15 mm deep, because the tap tip and the chip pile-up occupy the bottom. The drilling guide covers hole prep and chip control in detail.
Blind holes versus through holes
A through tapped hole is easy: the chip falls out the bottom and the tap runs free. A blind hole is where problems live. Chips have nowhere to go but back up the flutes, so the tap grinds on its own swarf and snaps. For blind holes, use a spiral-flute tap that pulls chips upward, or switch to thread milling, which cuts in controlled passes and clears chips cleanly. Design the hole a little deeper than you think you need, and add a small undercut or a relief at the thread end if the thread must run close to a shoulder. Mark the minimum thread engagement on the drawing rather than just “M6 x 1 deep”, because the machinist needs to know whether the bolt has to grip 6 mm or 12 mm.
Tapping versus thread milling
The two methods have different strengths. Tapping is fast and cheap for standard threads in through holes, but a broken tap in a blind hole often scraps the part. Thread milling uses a rotating tool that traces the thread profile, so one tool cuts a range of sizes, it works in blind holes with reliable chip control, and you can adjust the thread diameter in the program. Thread milling shines for large threads — M12 and up — where taps get expensive and fragile, and for hard materials where taps wear fast. It costs a bit more in machine time, but it removes the scrap risk. For most small M3 to M8 holes in aluminum and steel, tapping remains the default and the cheapest route. The thread milling versus tapping guide lays out the choice by size and material.
Material-specific pitfalls
Where you tap changes everything. In stainless, taps work-harden the hole if they dwell, so use sharp spiral taps and steady feeds; 304 and 316 are the grades that snap taps. In aluminum, chips weld to the tap, so cutting oil and polished flutes matter. In plastics, a tapped thread strips out under repeated assembly because the material creeps — for nylon, acetal, and PTFE, design a threaded insert (a brass or stainless heat-set insert) into the hole instead of tapping the plastic itself. Threaded inserts turn a soft plastic boss into a reusable steel thread, and they are the single most common fix for plastic assembly failures. The threaded inserts guide covers boss sizing and installation.
Designing the boss and the relief
Give the thread a home it can hold. A boss that is too thin cracks around the hole, so size the outside diameter at roughly twice the tap drill diameter for a robust boss. Keep the thread engagement at least one and a half times the bolt diameter in ductile materials — an M6 bolt wants about 9 to 10 mm of engagement in steel, and more in soft aluminum or plastic because they strip easier. Add a countersink or chamfer at the thread entrance so the bolt starts cleanly and you avoid a burr. Mark the class of fit — 6H for standard internal threads — so the shop cuts to the right tolerance. Get these four things right: correct tap drill, enough hole depth below the thread, a boss thick enough not to crack, and the right method for blind holes, and your threaded holes will assemble the way the drawing promises. The threading guide runs through the full thread toolkit for machined parts.
