Which surface finish belongs on a machined housing: the as-machined face the mill leaves, a blasted matte, an anodized coat, or a polished seal face? The question matters more than most buyers assume, because texture does more than change how the part looks. It controls fatigue life, sealing reliability, friction, paint adhesion, and how clean the component stays after years in service. Over-specifying texture across the whole drawing wastes money; under-specifying it on a functional face causes leaks and wear. The sections below cover what the machine leaves on its own, the finishes a shop can actually provide, the roughness numbers each one reaches, and how to call them out without paying for a surface nobody ever touches.
What the machine leaves on its own
Straight off a mill or lathe, every face carries the tool path. A conventional face mill on aluminum leaves roughly Ra 1.6 to 3.2; a turned finish on a rigid setup can hold Ra 0.8 to 1.6. These as-machined values add no cost, and for an internal, unseen component they are almost always the right choice. Every extra operation passes through programming, handling, and inspection, so a hidden pocket never benefits from a premium texture.
The trade-off is visibility. As-machined faces are directional, they show feed marks, and they read as raw on any housing the customer can see. Reserve secondary finishing for faces that seal, wear against another part, mount to a flat plane, or sit in view. The typical Ra bands for each available route are listed in our CNC surface finishing guide, which helps match the drawing callout to a real functional need rather than a habit.
Matte and blast textures for visible parts
Bead blasting removes the straight feed marks and leaves a uniform matte texture around Ra 1.5 to 2.5. It conceals minor tool marks and is the least expensive way to make a milled enclosure look deliberate and consistent. The finish hides fingerprints and light scuffs, which is why handles, brackets, and housings that get touched in service often receive it before anodizing or painting. What it cannot do is tighten a dimension or fix a wavy base; blasting only uniformizes the existing surface, it does not machine it flat. Our notes on bead blasting as a finish describe the texture buyers see on visible aluminum and steel housings.
Anodize, powder coat, and electroplating
Aluminum anodizing grows a controlled oxide layer. Type II runs 5 to 25 micrometers thick, accepts dye, and adds general corrosion resistance. Type III hard coat reaches 25 to 75 micrometers and builds a wear-resistant surface for sliding contacts. Because the oxide grows outward and into the base metal, the finished dimension grows by roughly half the coating depth on each exposed face, a point that matters on tight bores and slot widths. The anodizing aluminum guide compares Type II and Type III on wear, color, and dimensional growth.
Powder coating lays down a thick, tough film, usually 60 to 120 micrometers, and appears frequently on brackets and enclosures that need broad corrosion protection and a uniform painted look. Electroplating such as zinc-nickel or electroless nickel adds corrosion protection, but it deposits unevenly inside tight slots and small bores, so those features need a separate plan. Polishing and grinding push roughness down toward Ra 0.2 to 0.4, reserved for sealing faces and optical surfaces, and those processes carry real cost per square centimeter.
Reading an Ra callout and what it costs
Ra measures average roughness in micrometers, and tighter values are never free. Moving from Ra 3.2 to Ra 1.6 usually calls for a lighter final pass and sharp inserts, a modest price step. Dropping from Ra 1.6 to Ra 0.4 commonly requires grinding or polishing, and that can double the cost of that single face. The most common buyer trap is specifying Ra 1.6 across the entire housing when only one sealing face needs it.
Mark only the functional surfaces and leave the rest as-machined, then watch the quote fall. One mechanical housing priced with every face at Ra 1.6 commonly drops 15 to 25 percent once the callout moves to the sealing face alone. The numbers linking each Ra value to the process that reaches it are collected in the CNC surface roughness guide.
Match texture to the job the face performs
Function should decide the finish before appearance enters the conversation. A face compressed against an O-ring needs Ra 0.8 or better; a rough surface lets the elastomer leak and traps debris under the seal. A shaft rotating against a bushing needs a turned or ground finish near Ra 0.4 to 0.8 so it wears slowly over time. A threaded hole destined for paint should not be plated, because plating builds up in the threads and ruins the fit. Outdoor parts benefit from anodizing, chromate conversion, or powder rather than bare aluminum, which dulls to gray as it oxidizes.
- Sealing and gasket faces: Ra 0.8 or finer, after coat where required.
- Rotating or sliding journals: turned or ground, Ra 0.4 to 0.8.
- Visible housings: bead blast, then anodize or powder coat.
- Unseen internal pockets: leave as-machined.
Where finish jobs typically go wrong
Some problems come from choosing a texture the substrate cannot hold. Soft, gummy aluminum smears under a polishing wheel and leaves a wavy surface, so polishing requires a flat, already-machined base underneath. Plating and anodizing also change dimensions: a hole bored to +0.02 mm before anodizing can end up undersized after fifteen micrometers of coating builds on each wall, so the shop either bores after coating or oversize the bore beforehand.
Deburring cannot be skipped. Every later finish reveals the burrs left behind, which means the cleanup step belongs before plating rather than after. Marking a cosmetic finish on hidden faces only spends money, adds days to the schedule, and changes nothing the user ever sees. If the part will be painted, a blasted or primed surface holds the coating better than a glossy one, so the finish choice and the topcoat choice are linked rather than separate. Budget two to five extra business days for outsourced anodizing or plating, since these run on external cycles outside the machine. When the drawing is ambiguous, ask the shop which faces actually matter on your geometry and mark the remainder as as-machined.
