Stainless steel is stainless in name only. A 304 part fresh off the mill can look impressive for a week, then rust spots bloom at the first oily fingerprint, because free iron smeared onto the surface by tooling prevented the chromium oxide film from forming cleanly underneath. The surface finish selected for a stainless component is not decoration. It decides whether the part holds up in a kitchen, a chemical plant, or a coastal railing. Bead blast, passivation, electropolish, and mechanical polish each solve a different problem, and choosing the wrong one leads either to corrosion failure or to money spent on a finish the part never needed. This guide compares the four processes by what they remove, what they cost, and where each one belongs.
What each finish actually does to the surface
Bead blast fires fine glass or ceramic media at the part, leaving a uniform matte texture around Ra 1.2 to 2.5. It hides tool marks and fingerprints and remains the default for appearance components that do not need a mirror-smooth face. Passivation works chemically rather than abrasively: a nitric or citric acid bath dissolves free iron on the surface and lets chromium reform its protective oxide layer. It does not change roughness, so a Ra 1.6 part stays at Ra 1.6, yet it ranks as the single most important step for corrosion resistance, with ASTM A967 spelling out the process requirements.
Electropolish removes 0.01 to 0.03 millimeter of surface electrochemically, leaving a bright, passive, low-roughness face at Ra 0.2 to 0.8, and it becomes the choice for food and medical parts where cleanability drives the decision. Mechanical polishing reaches a mirror finish at Ra 0.1 or below, but it costs two to five times more than bead blast.
Each process targets a different surface problem rather than a single quality ladder from rough to smooth. Bead blast changes appearance by covering the existing texture with a uniform matte layer; passivation changes chemistry by restoring the oxide without touching topography; electropolish both removes material and adjusts chemistry in one electrochemical cycle; mechanical polish changes topography by hand abrasion. Confusing these purposes leads to the classic mistake of requesting electropolish for a cosmetic bracket, paying premium pricing for a cleanability process the part never requires.
The passivation guide goes deeper on the chemistry behind the oxide layer.
Cost and lead-time differences
Prices swing with part size and production volume, so the ranges below apply to small to medium components. Bead blast runs USD 15 to 40 per piece in batches of fifty and occupies one to three days of shop time. Passivation in a citric acid bath costs less, USD 5 to 20 per part in about one day, because it runs as a batch dip rather than a manual hand operation.
Electropolish sits at USD 40 to 120 per piece and adds three to five days, since racking the part to expose every surface becomes part-specific. Mechanical polishing to a mirror runs USD 80 to 250 per small piece, and because the work is hand-finished, lead times stretch to five to ten days. The practical takeaway: a component hidden inside an enclosure gets by with bead blast plus passivation for about ninety percent of its requirements at a fraction of the mirror-polish price.
Volume changes these numbers in predictable ways. Batch passivation and bead blast share racking and bath setup across dozens of parts, so the per-piece cost drops as the batch grows, while hand mirror polishing remains labor-bound by the part and never scales into a cheap per-unit operation. Odd-shaped components with blind holes or deep pockets also push electropolish pricing up, because the racking must keep every exposed face conductive and reachable by the bath. Quoting should therefore describe part geometry and batch size alongside the requested finish rather than sending a single dimensioned drawing and expecting a fixed surface price.
The bead blast finish guide lists media grit ranges and the typical Ra outcomes each produces.
Where each finish wins and where it loses
Bead blast wins on appearance consistency and on hiding existing scratches, but it loses on cleanability because the matte texture traps residue, which makes it the wrong choice for food-contact surfaces. Passivation wins on corrosion protection and costs almost nothing, yet it changes nothing about looks; a milled part after passivation still looks milled.
Electropolish wins on cleanability and on producing a passive surface, and it remains the only finish that removes the smeared metal layer left by machining. It loses on cost and struggles on parts with deep internal corners where the acid bath cannot reach. Mirror polish wins on optics and high-cleanliness vacuum service, but it scratches easily and shows every fingerprint left on the face. When choosing between mechanical and electropolished surfaces, the polishing versus grinding comparison walks through the roughness numbers side by side.
Specifying the process on the drawing
Write the finish by process standard rather than by vague adjective. A note reading bead blast, 120 grit glass media, Ra 1.6 to 2.5 carries more weight than one that says nice matte finish. For chemical treatment, write passivate per ASTM A967, citric acid, after machining and before assembly, rather than a shorthand passivate that leaves the bath choice to the shop.
When a part needs both bead blast and passivation, the sequence matters. Passivate after machining, then bead blast, then apply a final light citric dip; bead blasting before passivation embeds media into the surface and defeats the oxide cleanup. For food or pharma contact, call out electropolish to Ra 0.4 maximum and require a surface profile report. Stainless alloy selection remains half the equation: 303 machines freely but carries lower corrosion resistance because of its sulfur content, while 316 handles chloride exposure much better. The 303 versus 304 versus 316 guide covers that alloy side in detail.
Choosing the finish for the actual service
Run the component against its application before naming a process. A part in contact with food, pharma, or a clean gas path points to electropolish. A visible product surface that customers touch points to bead blast, with passivation underneath for corrosion protection. A hidden component that only needs to resist rust can rely on passivation alone, possibly left at a light mill finish.
Where the part sits in a coastal, chlorinated, or submerged environment, move to 316 or duplex 2205 before paying for a fancier surface treatment; the alloy matters more than the finish in those conditions. Whatever process is selected, apply it after all machining and welding are complete, because a scratched or heat-tinted surface undoes the whole treatment afterward. The stainless surface finishing guide provides the full table of processes, roughness targets, and typical pricing for each option, so the drawing can be tuned before it goes out for quote.
