Ra 3.2, Ra 1.6, Ra 0.4 — three roughness values that appear on nearly every machined drawing, yet the little check-mark symbol carrying them remains a mystery to most buyers. That surface texture symbol specifies roughness, waviness, and the machining method required for a face. Misread it and a hidden surface gets a mirror finish the budget never needed; ignore it on a seal face and the part leaks at Ra 3.2. This reference decodes the symbol itself, separates Ra from Rz, and shows how to call a finish out without arguing with the shop later.
Reading the basic symbol and its markings
The standard mark combines a check shape with a horizontal bar on top, and the numbers around it carry three distinct meanings. Roughness average, Ra, is the most common value, specified in micrometers from roughly Ra 0.05 for a mirror finish up to Ra 12.5 for rough as-milled stock. Maximum roughness, Rz, appears on seals and bearing surfaces because Ra alone can conceal a deep scratch that still breaks the seal.
- A bar across the top means material must be removed by machining.
- A circle on the bar means material removal is allowed but not required, or any method acceptable.
- A circle without the bar means stock must be left for a later operation.
- A number above the bar states the Ra ceiling; a number below the bar states machining allowance or maximum waviness.
- A symbol with no number at all means any finish acceptable — a gap the shop reads as as-milled, usually Ra 3.2 to 6.3.
The roughness bands buyers actually meet
Most drawings operate inside a narrow range, and matching the face to its band keeps cost controlled.
| Ra band | Typical surface | Common faces |
|---|---|---|
| 3.2 – 6.3 | As-milled or as-turned, visible feed marks | Non-critical faces, covers, brackets |
| 1.6 – 3.2 | Fine machined, marks barely visible at arm length | Mating surfaces bolted together |
| 0.8 – 1.6 | Nearly polished, reflects light softly | Seal faces, gasket surfaces |
| 0.4 and finer | Ground or polished, controlled roughness | Metal-to-metal seals, bearing journals, optical faces |
| 0.1 and below | Mirror, electropolished or lapped | Optical, food-contact, critical sealing |
The cost trap is specifying Ra 0.4 everywhere. That finish runs two to five times the cost of Ra 1.6 and buys nothing on a face nobody sees. The full Ra table with the machining process matching each value appears in our surface roughness guide.
What those values feel like on the finished part
Numbers alone do not convey the look. Ra 1.6 reads as a fine machined surface, with tool marks almost impossible to see at arm length. Ra 3.2 shows visible feed marks but remains perfectly functional. Ra 6.3 feels rough to the touch and is the usual default when nothing is specified. A Ra 0.8 face approaches a polished appearance and reflects light.
One detail surprises new buyers: the same Ra can come from different processes and look different. A milled Ra 1.6 carries directional feed lines, a ground Ra 1.6 looks uniformly matte, and a polished Ra 1.6 appears glossy. When appearance matters, call out the process alongside the value; milled Ra 1.6 and ground Ra 1.6 describe two visibly different parts. Visible surfaces also carry a lay direction — parallel, perpendicular, circular, or multidirectional — and a seal face with the wrong lay will leak under pressure.
Calling the finish out without arguments
Three rules keep shop and buyer working from the same interpretation. Place the symbol on the actual surface it governs rather than hiding it in a title-block note that reads all surfaces Ra 3.2; a blanket roughness across the whole drawing usually signals that the functional faces were never sorted out. On seal faces, distinguish Ra as an average from Rz as a maximum: Ra 0.8 paired with Rz 6 sits at risk of leaking, while Rz 3.0 under the same Ra performs fine. Add an explicit default note, such as all unspecified surfaces per Ra 3.2 unless otherwise noted, which removes the argument over what an empty symbol means. For a broader walk through GD&T, tolerances, and drawing symbols in order, see our guide to reading CNC drawings.
Common roughness mistakes and their fixes
The most frequent error asks a process for a finish it cannot hold without an extra operation. A milled face tops out around Ra 1.6 to 3.2, so calling Ra 0.4 on a milled pocket forces grinding or polishing and roughly doubles that face price. Another mistake mixes imperial and metric without translation: a drawing marked 63 microinch and one marked Ra 1.6 describe the same finish, since 63 microinch equals about Ra 1.6 micrometer, but a shop reading only one system quotes two different prices.
Roughness direction matters on dynamic seals and is easy to overlook. A rotating seal expects a circumferential lay; a reciprocating seal expects an axial lay. Swap the two and the seal wears out within months rather than years. When deciding between milling and grinding for a specific surface, the milling versus grinding comparison lists the finish ranges each process reliably holds, and the surface finish selection guide helps match the process to the Ra target on the drawing.
